ChemCo Systems - The experienced leader in concrete repair
PRODUCTS SERVICES EQUIPMENT & PARTS WHAT'S NEW COMPANY CONTACT

Equipment & Parts

Model C Epoxy Paste Pump

SITE SEARCH
Ports
Model B
> Model C
Model D
Parts & Service




The Model C is a portable unit for pumping 1:1 ratio high viscosity two component epoxy pastes and gels from 5-gallon pails. It uses 2 air-logic synchronized piston pumps to deliver high volumes of precisely mixed paste for patching, surface sealing, large crack filling, slot filling, dowel insertion or bolt/dowel/rebar grouting. It allows the contractor a freer choice of gel times and viscosities without worrying about batch mixing and wasted material. Bulk epoxies are far less costly than small disposable dual component cartridges. Flexible rubber follower plates automatically sweep the pail sides so waste is minimal. Sure beats buying a gazillion cartridges on large jobs! One of our contractors estimates that the Model C is 4 times faster than cartridges.

Specifications

General Designed to automatically meter, mix and pump two component, 1:1 ratio epoxy polymer adhesives in 5-gallon pails using air-driven components only. Eliminates off-ratio mixes and produces a controlled bead or flow rate for surface seals, large crack injection, and filling of slots, grooves and structural bolt or rebar anchors.
Design 4 wheel aluminum frame cart, with capacity to hold two-5 gallon pails for two component paste adhesives
Materials of construction Welded aluminum frame, wood base
Dimensions Height = 42", Width = 30", Length = 18"
Weight 45 lbs dry weight
Air controls Mounted on rear panel are pump piston control valves and regulators, vacuum bleed valve, shuttle valve, and air logic valves. Pump will cease operation unless both component pistons are within one stroke of each other
Air Motor speed Variable, from 0 to 145 c.p.m., controlled by pressure regulator
Speed & Flow Control Automatic by pressurer
Pump ON/OFF control Automatic pressure switch, set by operator
Noise level @ 120 p.s.i. < 85 d.b.a.
Pumps 2 Lincoln 50:1 Air motor driven with PTFE seals
Pump support cylinder Carries pump yoke and is raised and lowered by auxiliary air controls to position follower plates in pails
Stroke valves Attached to air logic controller—assure that 1:1 ratio is maintained. If either pump fails to complete a stroke, the air logic shuts down complete pump operation.
On/off control valve A remote valve controls paste pump operation from the work face with 20' of dual air line.
Mix Ratio 1:1 by volume
Ratio accuracy +/- 5% maximum error @ a 5 gallon/hour flow rate
Pumping pressure 0 to 5000 p.s.i. range
Pressure Control Automatic pressure switch set by operator
Delivery rate 0 to 25 gallons of mixed paste adhesive per hour
Delivery hoses 25 ft. in length, SAE type 100R7 with burst pressure rating of 11,000 p.s.i.
Mix head Aluminum body with three tandem mix chambers containing replaceable mix elements
Fitted with operator control valve
Special features Elastomeric pail wipers back stainless steel follower plates that scrape buckets clean on sides and prevent pump cavitation. Follower plates fitted with bleed air valves. Pump yoke (and follower plates) are air-operated with a raise/hold/lower air valve. No electric power is needed so pump can be operated in almost any environment including confined spaces.


Top of page
Model C air-driven epoxy pump for metering and dispensing 2 component epoxy pastes or gels
CCS PRODUCTS  |  KEMKO APPLICATORS  |  EPOXY ASPHALT  |  SERVICES  |  EQUIPMENT & PARTS  |  WHAT'S NEW  |  COMPANY  |  CONTACT  |  HOME
Toll Free: 800.757.6773   Tel: 650.261.3790   Email: email@chemcosystems.com